NP Pro

Np Pro Video Wall Controller Quick Start_V 1.6.4

1. Hardware preparation before commissioning:

Prepare a PC commissioning terminal that supports 1080P resolution and installs WIN10.

Np Lite equipment. (Np pro Chassis, HDMI cable, network cable, Gigabit switch.)

2. Safety check before use:

1. All displays are installed and powered on

2. Whether all HDMI, network cables and chassis power cable are connected

3. Whether chassis and others equipment are operating normally

3. Introduction to the device interface

4. Connection diagram

Input node: connect the signal source

Output node: connect to the screen

Input and output node: Input and output node both connect to switch.

Control PC: LAN connection/ network control connection control/ computer network cable.

5. Commissioning software installation and recognition:

5.1 Open the U disk to install the software

5.2 Video wall control system software icon

Account: admin

Password: admin

5.4 Enter the software interface

The software is stored with the equipment in the form of a U disk. For specific operations, please refer to the operation manual (the operation manual is stored with the equipment), or you can consult professional technicians.

6. Computer terminal control can be realized through the network gigabit switch

Modify the computer IP to ensure that it is in the same network segment as the Np Pro device.

Change the Ethernet IP address of the control computer to the same network segment. The default IP address of Np Pro is 192.168.0.200. You need to modify the IP address of the control computer to 192.168.0.xx. To change the IP address of the computer, you need to open the "Network Connection" window. Click on the window R, type "register password" in the run box, and then click the Enter key.

In the "Network Connections" window, right-click the adapter for which you want to set a static IP address, and then select the "Properties" command.

In the properties window of the adapter, select "Internet Protocol Version 4 (TCP/IPV4)", and then click the "Properties" button.

After entering the next page, just make the following modifications, and then click "OK" to save.

IP address: 192.168.0.200 (2~254)

Subnet mask: 255.255.255.0

Default gateway: 192.168.0.1

7. Set up

After saving, you can click NP Pro Video Wall Control System software. The software user name is admin, password: admin. The most important thing is to set the layout of the video wall first, click on " Display setting", and then click on "Layout".

Because my current screen is 2*3, I only need to change the ‘line’ value to 2 and the ‘column’ value to 3. If you have a vertical screen only at that time need to click on vertical mode which is mention in the upper image by yellow mark. Finally, click the save icon and save the layout setting.

Screen mapping:

Right-click the mouse on the output node shown on the left side of the interface and choose the on-screen test. After that video wall will show which output are connect with which screen. Now drag and drop all output according to display showing number. Save all this change and now it's ready to play.

8. Software operation

8.1 Multimedia Storage and Publishing

Click on the ‘‘resource’’ icon and import Local image / Video / Audio /text from your control pc to built-in storage, it can be called anytime and anywhere.

8.2 Display splitting Method

Select the window that needs to be split, right-click, click "Split-screen", select the number of split screens to split the screen.

8.3 Electronic Map

Click on "E-map" to go to the page of the electronic map. The electronic map monitoring operation interface consists of two parts.

1. IP Device List: Displays all IP devices added to the CVRD.

2. Electronic map area: Displays the added electronic map and the IP devices added on the map.

Double click on each IPC camera and it will be shown on the big screen.

8.4 Scene Management

Click the [Save Scene] button, pop up the interface of add scene. Fill in scene name, scene description, for example: set the current scene name to “1111111”, when you have done, click [ok].

9. Trouble Shooting

9.1 Some input signal was not showing in the signal list

l Check whether the main control computer RS232 is connected to the video wall control system. If not, please connect;

l Set the power switch on.

9.2 The serial port is occupied, the software can not find the serial port;

l Change the serial port number of the computer.

9.3 The device connection is unsuccessful

l First check whether the device LAN is connected, if the link is connected, check whether the connection is normal.

l After the connection is normal, check whether the device and the computer are in the same network segment.

As shown in the figure: